低压静电场辅助冷冻对竹笋品质的影响

为研究低压静电场辅助冷冻对竹笋冻结特性的影响，以冻结曲线、硬度、水分损失率、水分迁移、冰晶形态和组织微观结构为指标，探究低压静电场辅助冷冻（－35 ℃）和普通冷冻（－35 ℃）条件下竹笋品质的变化规律。结果表明：低压静电场辅助冷冻提高了冻结效率，改变了冰晶形态及分布，减轻了组织微观结构破损程度，改善了解冻汁液流失情况。与静电板间距10、20、30、40 cm处的冷冻竹笋解冻后水分损失率分别为14.16%、12.58%、9.73%、10.44%，显著低于对照组（21.01%）（P＜0.05），硬度分别为461.19、507.48、496.65 g和455.31 g，显著高于对照组（350.70 g）（P＜0.05）。低场核磁共振分析结果表明，在低压静电场辅助冷冻下竹笋解冻后汁液流失减少，扫描电子显微镜观察结果显示，竹笋纤维排列整齐，组织微观结构保持较好。低压静电场辅助冷冻可有效改善竹笋品质，可为利用低压静电场进行果蔬的冷冻贮藏和冷链运输提供参考。     

Ni-based catalysts with coke resistance enhance by radio frequency discharge plasma for CH4/CO2 reforming

Coke deposition has been considered to be one of the most important reasons hindering the stability of the catalyst during CH₄/CO₂ reforming. In this study, after the addition of P123 (PEG-PPG-PEG triblock copolymer), Ni²⁺ can be well-dispersed on the mesoporous molecular sieve MCM-41. And then, the catalysts were prepared by using N₂ radio frequency (RF) discharge plasma for different treatment times to reduce the size of Ni particles, improve the anti-coking performance, and thereby improve the stability of the catalyst. The results showed that the catalyst NM-P123-PN2h exhibits superior catalytic properties in the CH₄/CO₂ reforming. The initial conversions of CH₄ and CO₂ were 90.80% and 89.60% at 750 °C, respectively. The catalyst NM-P123-PN2h showed highly coke resistance with less carbon deposition (1.12%) at 750 °C after 10 h of continuous reaction, while the carbon deposition of the catalyst NM-C was 37.32%. Compared with the traditional calcination method, the catalyst prepared by plasma treatment has a smaller particle size and better dispersibility of nickel. In particular, the nickel particle size of the catalyst NM-C was 8.37 nm, however, that of the catalyst NM-P123-PN2h was only 1.70 nm, and the nickel particle size was reduced by 5 times. Therefore, it can be concluded that the catalyst prepared under the combined action of P123 and RF plasma-treated can effectively improve the coke resistance of the catalyst and the stability of the CH₄/CO₂ reforming.     

Evaluation of the localized corrosion on Mg electrode surface by electrochemical noise technique

The symmetrical and asymmetrical electrodes made of Mg were studied in 0.1-M NaCl electrolyte adjusted at pH 12. The statistical and wavelet methods were employed for analyzing the electrochemical current noise (ECN) signals. The asymmetric configuration was used for electrochemical detection of filiform corrosion on Mg electrode. The real time scale of the dominant transients of the asymmetric electrodes was detected on the basis of the maximum peak in the SDPS plots. The SDPS values of the real time scale crystals of the ECN signals resulting from asymmetrical electrodes increased with the increase in immersion time due to the onset of filiform corrosion.     

Superradiant Emission from Coherent Excitons in van Der Waals Heterostructures

Recent advancements in isolation and stacking of layered van der Waals materials have created an unprecedented paradigm for demonstrating varieties of 2D quantum materials. Rationally designed van der Waals heterostructures composed of monolayer transition-metal dichalcogenides (TMDs) and few-layer hBN show several unique optoelectronic features driven by correlations. However, entangled superradiant excitonic species in such systems have not been observed before. In this report, it is demonstrated that strong suppression of phonon population at low temperature results in a formation of a coherent excitonic-dipoles ensemble in the heterostructure, and the collective oscillation of those dipoles stimulates a robust phase synchronized ultra-narrow band superradiant emission even at extremely low pumping intensity. Such emitters are in high demand for a multitude of applications, including fundamental research on many-body correlations and other state-of-the-art technologies. This timely demonstration paves the way for further exploration of ultralow-threshold quantum-emitting devices with unmatched design freedom and spectral tunability.     

Research on H2/Air rotating detonation in the hollow chamber with double injection

In order to investigate the relationship between high frequency tangential instability and continuous rotating detonation, series of H₂/Air rotating detonations are experimentally achieved in the hollow chamber with double injection sections. In the center part, gaseous H₂ and air injected by co-axial injector. Near the outer wall, the same propellants are injected in the form of slit-orifice collision. By keeping the total air mass flow rate approximately constant, varying the mixture of the inner and outer injection, series experiments are conducted in the test model with or without Laval nozzle. The results verify the possibility of rotating detonation in the hollow chamber with co-axial injector. To clarify the relationship between continuous rotating detonation and high frequency tangential combustion instability, the intrinsic frequencies of the test model are captured to be compared with propagation frequencies of detonation waves. The results show that they are close to each other when enough propellant assembled near the outer wall. In the combustor, the flame direction in constant pressure mode can change itself into rotating direction spontaneously. The results indicate that rotating detonation is an implication to high frequency tangential instability.     

典型废玻璃回收厂区空气颗粒物及噪声分布特征研究

以某典型废玻璃回收厂区作为研究对象, 监测和分析了车间及厂区内部的噪声强度、空气颗粒物(PM_2.5、PM₁₀) 浓度等环境指标, 点位布设涵盖了车间入口、人工分拣、物料筛分、破碎、干法清洗等关键工艺环节; 其次, 解析了空气颗粒物的组分及形貌特征, 并对其在厂区及车间内部的时空分布特征进行了研究; 此外, 利用噪声控制模型模拟并分析了隔声罩对噪声的控制作用。结果表明, 生产车间中工作态的空气颗粒物浓度显著高于非工作态, 其中干法清洗区浓度最高, 其PM_2.5 浓度为3.725 mg/m³, PM₁₀浓度为4.055 mg/m³; 噪声监测结果显示生产车间内噪声强度较高, 达到99.5 dB, 而引入隔声罩后噪声强度可降至67 dB, 结果表明, 隔声罩可有效控制频率为125~1 000 Hz 的噪声。该研究可为废玻璃的绿色、高效回收处置提供理论基础和实践经验。     

基于电信号特征分析的电机故障诊断技术

介绍了电机故障诊断技术平台的组成,分析了电机常见故障下电信号的特征。利用宜昌和景洪工厂两台电机进行了实际对比测试,宜昌工厂电机定子电流特征频率在49.2Hz时表现出峰值-36.08dB,在50.8Hz时表现峰值则为-37.23dB,表明电机存在转子断条故障;景洪工厂电机在转子特征频率为113.51Hz时,出现峰值-58.47dB,表明电机存在静态偏心故障。经电机现场抽芯检查,验证了电机故障快速诊断平台给出的电机健康状态评估结果,证实了基于电信号特征分析的电机故障诊断技术的准确性。     

Rational Designs for Lithium-Sulfur Batteries with Low Electrolyte/Sulfur Ratio

Lithium-sulfur batteries (LSBs) are considered a promising next-generation energy storage device owing to their high theoretical energy density. However, their overall performance is limited by several critical issues such as lithium polysulfide (PS) shuttles, low sulfur utilization, and unstable Li metal anodes. Despite recent huge progress, the electrolyte/sulfur ratio (E/S) used is usually very high (≥20 µL mg⁻¹), which greatly reduces the practical energy density of devices. To push forward LSBs from the lab to the industry, considerable attention is devoted to reducing E/S while ensuring the electrochemical performance. To date, however, few reviews have comprehensively elucidated the possible strategies to achieve that purpose. In this review, recent advances in low E/S cathodes and anodes based on the issues resulting from low E/S and the corresponding solutions are summarized. These will be beneficial for a systematic understanding of the rational design ideas and research trends of low E/S LSBs. In particular, three strategies are proposed for cathodes: preventing PS formation/aggregation to avoid inadequate dissolution, designing multifunctional macroporous networks to address incomplete infiltration, and utilizing an imprison strategy to relieve the adsorption dependence on specific surface area. Finally, the challenges and future prospects for low E/S LSBs are discussed.     

Microstructure,tribological behavior and magnetic properties of Fe−Ni−TiO2 composite coatings synthesized via pulse frequency variation

The Fe−Ni−TiO₂ nanocomposite coatings were electrodeposited by pulse frequency variation. The results showed that the nanocomposite with a very dense coating surface and a nanocrystalline structure was produced at higher frequencies. By increasing the pulse frequency from 10 to 500 Hz, the iron and TiO₂ nanoparticles contentswere increased in expense of nickel content. XRD patterns showed that by increasing the frequency to 500 Hz, an enhancement ofBCC phase was observed and the grain size of deposits was reduced to 35 nm. The microhardness and the surface roughness were increased to 647 HV and 125 nm at 500 Hz due to the grain size reduction and higher incorporation of TiO₂ nanoparticles into the Fe−Ni matrix (5.13 wt.%). Moreover, the friction coefficient and wear rate values were decreased by increasing the pulse frequency;while the saturation magnetization and coercivity values of the composite deposits were increased.